Mts SWIFT 10 MC Sensor Uživatelský manuál Strana 127
- Strana / 144
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
THE INFORMATION AND DESIGN(S)
D
ISCLOSED HEREIN ARE CONFIDENTIAL
AND THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY
FORM EXCEPT AS GRANTED IN WRITING
BY MTS SYSTEMS CORPORATION. THIS
RESTRICTION EXCLUDES INFORMATION
THAT IS IN THE PUBLIC DOMAIN OR
WAS LEGITIMATELY IN THE PRIOR
POSSESSION OF THE RECIPIENT.
PROPRIETARY DATA
SOURCE/REF
DRAWING
MATERIAL DESCRIPTION
MATERIAL SIZE
FINISH
MASK
M
THREAD DEPTHS ARE TO MIN FULL THDS
DRILL DEPTHS ARE TO FULL DIA
REMOVE BURRS AND SHARP EDGES
DO NOT SCALE PRINT
SCALE
MACHINED
SURFACES
180
UNLESS OTHERWISE SPECIFIED
.XXX HOLE SIZE TOLERANCE
0.000
TO .750
+.010/-.002
OVER .750
TO 1.500
+.015/-.003
ANGLE 2
GENERAL
TOLERANCES
X
Y
.X
.XX
.XXX
THIRD
ANGLE
PROJ
C
MTS SYSTEMS CORPORATION
ED
EN PRAIRIE, MINNESOTA U.S.A.
1/4
.1
.03
.010
DRAWN
C
HECK
ENGR
DATE
MFG
DATE
DATEDATE
SIZE
TITLE
NEXT LEVEL
PRODUCT CODE
NUMBER
SHEET OF
REV
D
REVISIONS
DATE
EN
GR
DRAWN
LETTER
ECN NO
DESCRIPTION
m
4
RLJ
R
AM
7-07
7-07
2
5
100-180-624
RIM ASSEMBLY-FRONT,
21 X 1.60 RIM, SWIFT 10
C
11
20
19
9
INNER HUB ASSEMBLY
(
NON-BRAKE SIDE)
AXLE SPACER
SEALED BALL BEARING
LOAD SPACER
SEALED BALL BEARING
AXLE SPACER
OIL SEAL
LOAD SPACER
27
PLUG SEAL
28
2
O-RING
B
B
4
5
5
6
4
.040 [1MM] GAP
SECTION B-B
A
PPLY GREASE ON DIAMETER,
TO REDUCE FRICTION BETWEEN
AXLE SPACER AND OIL SEAL
11
20
9
19
5
INNER HUB ADAPTER
O
IL SEAL
5
INNER HUB ADAPTER
N
OTES (CONTINUED):
APPLY A SMALL AMOUNT OF OIL/LUBRICANT TO OUTER DIAMETER OF BEARING (ITEM 19) AND
PRESS IN TO INNER HUB (ITEM 5), UNTIL BEARING HAS A 1MM (.040") GAP FROM SHOULDER
AS SHOWN. IT IS IMPORTANT THAT THE BEARING IS PRESSED IN ON THE OUTER RACE.
PRESS IN OIL SEAL (ITEM 20) INTO HUB, UNTIL IT FULLY RESTS AGAINST SHOULDER.
PRESS AXLE SPACER (ITEM 11) INTO OIL SEAL, UNTIL IT FULLY RESTS AGAINST THE BALL BEARING.
THE LOAD SPACER (ITEM 9) SHOULD THEN BE PLACED ON THE END OF THE AXLE SPACER.
6
- SWIFT® 10 MC Sensor 1
- Product Information 1
- Publication information 2
- Contents 3
- Maintenance 97 4
- Troubleshooting 101 4
- Assembly Drawings 113 4
- Technical Support 5
- If You Contact MTS by Phone 7
- Before You Begin 9
- Conventions 10
- SWIFT 10 MC Sensors Preface 11
- Hardware Overview 13
- Overview 14
- Parts replacement 15
- S10MC-03 17
- Construction 18
- Transducer Interface 20
- Additional 20
- Design Features 21
- Coordinate System 22
- Specifications 24
- Transducer Center-of-Gravity 25
- ALUMINUM TITANIUM 25
- ARAMETER SPECIFICATION 26
- Calibration 27
- Checking the 28
- TI Front Panel 32
- TI Rear Panel 33
- Interfacing with RPC 34
- Software Utilities 35
- Introduction 36
- Syntax ti2xfer 39
- More about TI2XFER 40
- Syntax ti2shunt 41
- Error Messages 44
- USB Driver Installation 48
- Select a Zero Method 50
- Calibration File Elements 51
- Upload the Calibration File 52
- Edit the Calibration File 53
- Download the Calibration File 56
- Installing the Transducer 57
- Hazard Icon 58
- Road and Track Vehicles 59
- S10MC-08 60
- UANTITY FRONT AND REAR 62
- ORQUE INCREMENT M8 BOLT SIZE 65
- Data Recorder 73
- the Z axis facing 74
- Axes Icon 75
- S10MC-17 76
- Shunt Button 77
- Effect of zero 78
- Collecting Data 79
- Road Simulator 81
- S10MC-22 85
- S10MC-13R 88
- Transducer 98
- SWIFT 10 MC Sensors 100
- Maintenance 100
- Troubleshooting 101
- Signal Outputs appear to 104
- TI electronics have been 104
- value is 105
- value is set in the TI 105
- Signal Outputs appears to 105
- Troubleshooting Guide 106
- Shunt Calibration 107
- Assembly Drawings 113
- Cable Drawings 115
- SWIFT 10 Mechanical Drawings 121
- PROPRIETARY DATA 126
- REVISIONS 126
Související produkty a manuály pro Hardware Mts SWIFT 10 MC Sensor
Hardware Mts Criterion Series 40 Uživatelský manuál
(48 stránky)
(48 stránky)
Hardware Mts Criterion Series 60 Uživatelský manuál
(42 stránky)
(42 stránky)
Hardware Mts Criterion Series 40 Uživatelský manuál
(142 stránky)
(142 stránky)
Hardware Mts Criterion Series 60 Uživatelský manuál
(146 stránky)
(146 stránky)
Hardware Mts 85X Damper Uživatelský manuál
(56 stránky)
(56 stránky)
Hardware Mts Landmark Tabletop Uživatelský manuál
(122 stránky)
(122 stránky)
Hardware Mts TestLine Uživatelský manuál
(132 stránky)
(132 stránky)
Hardware Mts Attuatori serie 248 Uživatelský manuál
(50 stránky)
(50 stránky)
Hardware Mts Vérins série 201 Uživatelský manuál
(40 stránky)
(40 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce