Mts SWIFT 40 Sensor Uživatelský manuál Strana 76
- Strana / 170
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SWIFT 40 Sensors
76
Test Track Vehicle
Installing the Transducer
5. Attach the hub adapter to the transducer. Hand tighten the bolts.
If environmental conditions warrant, coat each fastener with Birchwood
Casey Sheath RB1 rust preventative (or equivalent).
Lubricate the threads and under the heads of all fasteners, using Molykote
g-n paste.
A clearance of approximately 0.05 mm (0.002 in) is required between the
transducer and the hub adapter. You should not have to wedge the wheel into
the rim or the hub adapter into the SWIFT sensor.
Bolt Torque Sequence
6. Tighten the mounting bolts.
A. Following the sequence shown in the previous figure for the transducer
being installed, torque the four M8 bolts in two increments as shown in
the following table.
Important The M8 bolts in the inner bolt pattern (bolts A–D in the previous
figure) must be torqued, as described, before torquing the M10
bolts.
B. Following the sequence shown in the previous figure for the transducer
being installed, torque the twenty-four M10 inner hub bolts in two
increments as shown in the following table.
Inner Bolt Pattern
Bolts AD are M8
Bolts 124 are M10
A
D
B
C
15
9
17
13
24
20
12
7
3
15
22
18
10
6
2
14
23
19
11
8
21
16
4
4
16
17
9
5
1
13
20
12
7
3
15
18
10
62
14
19
11
8
SWIFT 40
Viewed from Pilot Side
Outer Bolt Pattern
All Bolts are:
M10 for Aluminum Transducers
M14 for Titanium Transducers
S40-16
- SWIFT® 40 Sensor 1
- Product Information 1
- Publication information 2
- Contents 3
- Analyzing SWIFT Data 105 4
- Maintenance 117 5
- Troubleshooting 121 5
- Assembly Drawings 135 5
- If You Contact MTS by Phone 9
- SWIFT 40 Sensors 10
- Technical Support 10
- Before You Begin 11
- Conventions 12
- SWIFT 40 Sensors Preface 13
- Hardware Overview 15
- Construction 18
- Non-spinning 20
- Additional 21
- Design Features 22
- Coordinate System 23
- Specifications 25
- Transducer Center-of-Gravity 26
- ALUMINUM TITANIUM 26
- ARAMETER SPECIFICATION 27
- ARAMETER SPECIFICATION 28
- Calibration 29
- Checking the 30
- TI Front Panel 34
- AngleFixed=0 35
- LGORITHM 36
- of range) occurred on 39
- AIL INDICATOR STATE 40
- TI Rear Panel 41
- TI Jumpers 42
- Interfacing with RPC 43
- Software Utilities 45
- Introduction 46
- More about TIXFER 49
- Error Status,” on page 58 51
- Error Messages 57
- Shunt Error Status 58
- Select a Zero Method 60
- Calibration File Elements 61
- Zero Algorithms 62
- Upload the Calibration File 64
- Edit the Calibration File 65
- UTPUTS MZ MY MX FZ FY FX 66
- Z MY MX FZ FY FX 66
- Description 67
- Download the Calibration File 69
- Test Track Vehicle 72
- OLT SIZE 77
- ORQUE INCREMENT M8 M10 M14 77
- Considerations for 82
- Choosing a Zero 83
- Axes Icon 85
- Angle Zero 86
- Switch and Indicator 86
- Bridge Zero 86
- SWIFT 40 A (Aluminum) 91
- SWIFT 40T (Titanium) 91
- Effect of Zero 92
- Reference on SWIFT 92
- Collecting Data 94
- Road Simulator 100
- Installing the Transducer 100
- Communication Configurations 102
- Cable Configurations 103
- Termination Jumper 104
- Analyzing SWIFT Data 105
- The Data 106
- Fx Data (Longitudinal Force) 107
- Fx Offset=165N 108
- Fz Data (Vertical Force) 109
- Mx Data (Overturning Moment) 110
- My Data (Brake Moment) 113
- Slalom Curve Driving Example 116
- Maintenance 117
- Transducer 118
- Transducer Interface 119
- Troubleshooting 121
- Signal Outputs appears to 124
- TI electronics have been 124
- One or more 126
- Troubleshooting Guide 127
- Assembly Drawings 135
- Cable Drawings 136
- SWIFT 40A Mechanical Drawings 151
- SWIFT 40T Mechanical Drawings 155
- Common Parts 161
Související produkty a manuály pro Hardware Mts SWIFT 40 Sensor
Hardware Mts SWIFT 45 GLP Sensor Uživatelský manuál
(106 stránky)
(106 stránky)
Hardware Mts SWIFT 50 GLP Sensor Uživatelský manuál
(70 stránky)
(70 stránky)
Hardware Mts SWIFT 10 ATV Sensor Uživatelský manuál
(144 stránky)
(144 stránky)
Hardware Mts Series 249 Swivels Uživatelský manuál
(40 stránky)
(40 stránky)
Hardware Mts SWIFT 10 MC Sensor Uživatelský manuál
(144 stránky)
(144 stránky)
Hardware Mts Criterion Series 40 Uživatelský manuál
(48 stránky)
(48 stránky)
Hardware Mts Criterion Series 60 Uživatelský manuál
(42 stránky)
(42 stránky)
Hardware Mts Criterion Series 40 Uživatelský manuál
(142 stránky)
(142 stránky)
Hardware Mts Criterion Series 60 Uživatelský manuál
(146 stránky)
(146 stránky)
Hardware Mts 85X Damper Uživatelský manuál
(56 stránky)
(56 stránky)
Hardware Mts Landmark Tabletop Uživatelský manuál
(122 stránky)
(122 stránky)
Hardware Mts TestLine Uživatelský manuál
(132 stránky)
(132 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce