Mts ReNew Technical Reference Uživatelský manuál Strana 1

ReNew Technical Referencel100-178-163 A

ReNew Technical Reference10Contacting MTSPrefaceContacting MTSMTS provides a full range of support services after your system is installed. If you hav

Contacting MTSReNew Technical Reference Preface11What to Expect When You CallNote Some of the following information specifically discusses what to exp

ReNew Technical Reference12Contacting MTSPrefaceKnow relevant computerinformationIf you are experiencing a computer problem, have the following inform

ReNew Technical Reference Introduction13IntroductionThe ReNew®and ReNew SMA®Upgrade System product series are the latest generation of system upgrade

ReNew Technical Reference14DescriptionIntroductionDescriptionGeneral description The ReNew products allow the user to utilize the latest control elect

DescriptionReNew Technical Reference Introduction15Controller functions All ReNew systems are controlled by MTS's latest precision frame controll

ReNew Technical Reference16DescriptionIntroductionThe ReNew SMA When a material testing system to be upgraded has a functioning servomotor and amplifi

SpecificationsReNew Technical Reference Introduction17SpecificationsEnvironmentalspecifications(indoor use only)Individual ReNewmodel specificationsRe

ReNew Technical Reference18SpecificationsIntroductionReNew SMA andReNew SMA-DAPhysicalHeight460 mm (18.1 in)Width180 mm (7.1)Depth432 mm (17.0 mm)Weig

ReNew Technical Reference Installation19InstallationLocation andventilationAll ReNew boxes can be placed on the floor next to or behind a floor-standi

Copyright information © 2007 MTS Systems Corporation. All rights reserved.Trademark information MTS and TestWorks are registered trademarks of MTS Sys

ReNew Technical Reference20InstallationAppliance inletconfigurationsThe ReNew Elite has an IEC 60320 C20 appliance inlet. The conductor configuration

ReNew Technical Reference Installation21External earthconnectionThe ReNew systems have an additional ground connection on the rear of the enclosure. T

ReNew Technical Reference22InstallationThis switch must be located no more than 1 meter from the test space and must be rigidly attached to the machin

ReNew Technical Reference Installation23ReNew Elite systemconnectionsCable Description MTS #1 CABLE-USB V2.0 CABLE,A-B,3 METER/10 FOOT 100-096-4192 CA

ReNew Technical Reference24InstallationReNew SMA systemconnectionsOn Instron 4400 frames, the control cable (#2 above) plugs into the existing handset

ReNew Technical Reference Installation25For these applications the existing motor, amplifier, controls, and signal conditioning must be functional. Th

ReNew Technical Reference26InstallationInstalling cablesExercise care when connecting cables. Ensure that you are using the correct cables and that al

ReNew Technical Reference Installation27J8—DC Conditioner 2. Could be strain based extensometer, second load cell, or high level analog output sensor.

ReNew Technical Reference28InstallationJ2 Handset This is intended to interface to the handset. Specifics for this connector are:• 12 V output power w

ReNew Technical Reference Installation29J3 Interlock This is intended to connect to a test area enclosure switch that opens when the door is opened. I

ReNew Technical Reference Contents3ContentsPreface 5About This Manual 6Conventions 7Contacting MTS 10What to Expect When You Call 11Int

ReNew Technical Reference30InstallationJ5 Digital I/O Digital I/O signals include three optically isolated inputs, three optically isolated outputs, a

ReNew Technical Reference Installation31J6 and J7MonitorTwo Monitor connectors are provided. There are several possible uses for analog monitor output

ReNew Technical Reference32Installation

Handset ControlReNew Technical Reference Operation33OperationHandset ControlThe handset has an encoder and buttons to help you during specimen install

ReNew Technical Reference34Handset ControlOperationHandset functions The handset is intended to be used in a system for specimen loading or setup. In

Handset ControlReNew Technical Reference Operation35Safety Symbols(inside)These symbols are present “inside” the testing system enclosure.Item Descrip

ReNew Technical Reference36Handset ControlOperationTravel limit switches(Physical limits)The manner in which limit switch adjustments are made varies

Handset ControlReNew Technical Reference Operation37

ReNew Technical Reference38Handset ControlOperation

ReNew Technical Reference Maintenance39MaintenanceDisconnect the power cord from the wall outlet before cleaning or lubricating any part of the test f

ReNew Technical Reference4Contents

ReNew Technical Reference40MaintenanceSemiannualmaintenance1. Remove system covers and vacuum or blow out any dust or debris from inside the test fram

ReNew Technical Reference Troubleshooting Guide41Troubleshooting GuideUse this chapter to identify mechanical and electronic problems with your ReNew

ReNew Technical Reference42Troubleshooting GuideCrosshead will not stop • Servo is improperly connected.• Improper machine parameters. Contact an MTS

Additional Digital I/O InformationReNew Technical Reference Appendix43AppendixAdditional Digital I/O InformationThe digital inputs have an MOCD223 opt

ReNew Technical Reference44Additional Digital I/O InformationAppendixA typical example might be connecting an external switch.Insight ControllerIN 1-G

ReNew Technical Reference Configuration Drawings45Configuration DrawingsThe following Insight Renew Board Jumpers & Fuses configuration chart is i

ReNew Technical Reference46Configuration Drawings

Schematic DWG: 700-003-357 Deviations on DesignatorDescription Dwg Sheet Mong - Elite & SMAMong - Alliance ADC - GFCC QFCC This System:X1 Install

100-178-163 MWC Reision A

ReNew Technical Reference Preface5PrefaceSafety first! Before you attempt to use your MTS product or system, read and understand all safety informatio

mMTS Systems Corporation14000 Technology DriveEden Prairie, Minnesota 55344-2290 USAToll Free Phone: 800-328-2255(within the U.S. or Canada)Phone: 952

ReNew Technical Reference6About This ManualPrefaceAbout This ManualPurpose This manual provides detailed information about the ReNew™ and SMA Upgrade

About This ManualReNew Technical Reference Preface7ConventionsThe following sections describe some of the safety conventions that are used in your MTS

ReNew Technical Reference8About This ManualPrefaceWarning notices Warning notices indicate the presence of a hazard which can cause severe personal in

About This ManualReNew Technical Reference Preface9Safety Symbols These symbols are present on the exterior of the testing system.Other conventionsNot